Misc. Electronics

Products

  •  per page
AEM 4-Channel K-Type Thermocouple Amplifier
Part #: 30-2204
4-channel K-type thermocouple amplifier.

AEM's 4-Channel K-Type Thermocouple Amplifier provides laboratory-grade accuracy for virtually any on-board temperature measurements. This unit utilizes low-cost K-Type thermocouple amplifiers to measure multiple engine system temperatures with better accuracy and faster response times than currently available temperature-measuring devices.

Unlike common single-channel gauges and amplifiers whose readings can vary up to 20? C from actual temperatures, AEM guarantees its 4-Channel K-Type Thermocouple Amplifier to read better than 1% full scale, even at the extremes of the temperature range! The unit achieves its laboratory-grade accuracy via a 100% surface-mounted PCB (printed circuit board) that has four differential temperature inputs fed into an A/D converter and fitted using a stage-three, eighth-order polynomial curve fit. The amplifier then compensates for this value using AEM's on-board cold junction temperature measurement, and then sends the temperature outputs on feedback-monitored 0-5v analog outputs and an RS-232 serial data stream.

The 4-Channel K-Type Thermocouple Amplifier is ideal for users who want to accurately monitor multiple engine system temperatures, including water, air, coolant, fuel, disc brake and more. Multiple channels allow you to use each amp to simultaneously read different system temperatures (one channel for EGT, one channel for CLT, etc.). Users can utilize ANY K-Type thermocouple including commonly-available miniature thermocouple connectors, and datalog the readings via an RS-232 serial data stream. K-Type sensors sold separately.

Uses common miniature thermocouple connectors or ANY K-Type thermocouple
On-board cold junction temperature compensation for laboratory-grade accuracy
Includes FOUR (4) 0-5v analog outputs
0-1,000? C(32-1,832? F) measurement range
Measures up to 20? C below cold junction temperature
RS-232 serial port included for datalogging (programmable EMS not required)
"Fault LEDs" indicate when a thermocouple is faulty
High-quality Deutsch connector
Mating harness included


Our price: $325.62
Quantity Out of stock
AEM 5 Bar External Sensor Kit : For AEM TRU-BOOST
Part #: 30-4351

The AEM 5 Bar External Sensor kit allows you to run boost levels higher then 29psi.

Fits: AEM TRU-BOOST Gauge Type Boost Controller # 30-4350

Part # 30-4351

Not CARB legal: Not for sale or street use in CA & CARB states.


Our price: $195.36
Quantity
AEM 72" Serial EMS Coms Cable
Part #: 35-3001
72" serial EMS coms cable.

AEM offers several sensor and Plug & Pin connector kits for vehicles that require additional outputs and/or upgraded hardware over existing sensors. Available sensors include boost/backpressure sensors, exhaust gas temperature (EGT) sensors, nitrous oxide/brake pressure sensors, UEGO replacement sensors, inlet air temp sensors (IAT), K-Type sensors and more. All sensors come with a three- wire mating connector with 12" leads for ease of installation.

High-quality sealed sensor housings
Mating connector and 12" leads included (sensors)
Accurate and affordable!


Our price: $8.95
Quantity
AEM 96" UEGO Sensor Replacement Cable for "Gauge-Type" Controller
Part #: 35-3400
96" UEGO sensor replacement cable for "Gauge-Type" Controller.

AEM offers several sensor and Plug & Pin connector kits for vehicles that require additional outputs and/or upgraded hardware over existing sensors. Available sensors include boost/backpressure sensors, exhaust gas temperature (EGT) sensors, nitrous oxide/brake pressure sensors, UEGO replacement sensors, inlet air temp sensors (IAT), K-Type sensors and more. All sensors come with a three- wire mating connector with 12" leads for ease of installation.

High-quality sealed sensor housings
Mating connector and 12" leads included (sensors)
Accurate and affordable!


Our price: $30.95
Quantity
AEM Peak & Hold Injector Driver Module: Universal
Part #: 30-2710

Peak & hold injector driver. 10 injectors.

AEM's external Peak & Hold Injector Driver module allows ECU's that have a saturated injector drive circuit to trigger low impedance injectors with a true 4/1 Peak & Hold injector drive circuit.

AEM's Peak & Hold Injector Driver contains 10 independent injector drive channels. Each channel supplies full battery voltage to a fuel injector for rapid current rise, in order to produce positive injector opening. When load current reaches 4.1A (amps), the injector driver reduces the load current to 1.1A and operates as a constant current source. This condition holds the injector open, and reduces system power dissipation. If the current fails to reach 4.1A within 5mS, the driver module automatically reduces the load current to 1.1A.

Installation is straightforward. Users simply hook the injector trigger wires from an ECU to the module, and then hook the output wires from the module to your injectors. Any number of channels can be used from one to 10.

*Legal in California only for racing vehicles which may never be used upon a highway.

For high-output racing engines that have exceeded the capacity of high-impedance injectors
Includes 10 independent injector drive channels for any engine up to V10
Complete wiring system included
Operating Voltage: 8-18 volts, negative ground
RPM Capability: Unlimited
Injector Triggers: 10
Trigger Waveform: Output is activated when input trigger is grounded
Trigger Impedance: 220 Ohm input impedance, pulled to 12V (60 mA draw)
Injector Outputs: 10
Output Current High: 4.15A Peak, Typical
Output Current Low: 1.15A Sustain, Typical
Peak Current Timeout: 5mS
Size: 5.5"L x 4.6"W x 1.4"H
Weight: 2.7 Lbs
Over Temperature Shutdown: 115C (Nominal)

Not CARB legal: Not for sale or street use in CA & CARB states.


Our price: $327.28
Quantity
AEM Plug-N-Pin Kit for EMS 30-1010, 1012, 1020, 1050's, 1052's & 1060's
Part #: 35-2610
Plug-N-Pin Kit for EMS 30-1010, 1012, 1020, 1050's, 1052's & 1060's

AEM's high-quality, color-coded master wiring harnesses include everything you need to properly wire your racecar in one easy-to-follow configuration (sold separately). We silk-screen each individual wire function onto the body of the wire to ease the installation process and reduce any chance of misidentifying a wire during set-up.

AEM's 72" master wiring harness includes built-in fuses and relays for fans, pumps, auxiliary power, and more. AEM also has a 24" wiring harness for adapting our Universal EMS system to an exiting wiring race car harness, and harness mating connector kit with 104 contacts.

*Legal in California only for racing vehicles which may never be used upon a highway.

Color coded harness has bundle identifiers and includes silk-screened functions on wire body for easy identification
Includes integrated fuse box with relays for fans, pumps, auxiliary power and more
Bolt-in plug mates to AEM Universal EMS and eliminates any chance of separation


Our price: $61.76
Quantity
AEM Plug-N-Pin Kit for EMS 30-1900 & 30-1902
Part #: 30-2902

Plug-N-Pin Kit for EMS 30-1900 & 30-1902

AEM's high-quality, color-coded master wiring harnesses include everything you need to properly wire your racecar in one easy-to-follow configuration (sold separately). We silk-screen each individual wire function onto the body of the wire to ease the installation process and reduce any chance of misidentifying a wire during set-up.

AEM offers several sensor and Plug & Pin connector kits for vehicles that require additional outputs and/or upgraded hardware over existing sensors. Available sensors include boost/backpressure sensors, exhaust gas temperature (EGT) sensors, nitrous oxide/brake pressure sensors, UEGO replacement sensors, inlet air temp sensors (IAT), K-Type sensors and more. All sensors come with a three- wire mating connector with 12" leads for ease of installation.

* High-quality sealed sensor housings
* Mating connector and 12” leads included (sensors)
* Accurate and affordable!

*Legal in California only for racing vehicles which may never be used upon a highway.

Color coded harness has bundle identifiers and includes silk-screened functions on wire body for easy identification
Includes integrated fuse box with relays for fans, pumps, auxiliary power and more
Bolt-in plug mates to AEM Universal EMS and eliminates any chance of separation


Our price: $78.75
Quantity
AEM Serial Datastream Gauge : 30-4300
Part #: 30-4300

19 Gauges In One! AEM’s Serial Gauge plugs into the company’s Programmable EMS and has the ability to read 19 channels simultaneously to provide reference for all outputs, including boost, AFR, EGT, H2O, IAT, knock, volts, RPM, vehicle speed, and more! Since it can read all channels at once, AEM’s Serial Gauge eliminates the need to buy a cluster of gauges, or you can link multiple Serial Gauges together to monitor additional channels or to divide your readouts across a few gauges.

Key Features:

• Monitor 19 channels simultaneously—it’s like having 19 gauges in one!

• Works with AEM Programmable Engine Management Systems Only

• User-programmable datastream channels (PC interface)

• User-programmable MIN/MAX values for every channel (PC interface)

• Includes two input buttons for scrolling through displayed channels and for clearing MIN/MAX values

• 24 user-programmable LEDs and three-digit center display (PC interface)

• User-selectable alarm values include qualifiers to eliminate false warnings

• User-selectable alarm priorities in the event multiple alarms are triggered

• Two outputs included to trigger ancillary warning lights or other devices (lights not included)

• Silver and black bezels and pin guides, and black and white faceplates included for creating custom look

• Quick-Connect technology eases installation• Standard 52mm gauge housing fits in most pods and can be remotely mounted virtually anywhere

• All necessary hardware and software included for installation

TECH TIP: You will need to be using theAEM Engine management system to run this gauge.

Part #  30-4300


Not CARB legal: Not for sale or street use in CA & CARB states.


Our price: $203.95
Quantity
AEM Universal 1 Bar Map or 15 PSIA Sensor Kit
Part #: 30-2130-15
1 bar map or 15 PSIA sensor kit. Stainless steel sensor body with 1/8-NPT male thread. Includes -4 adaptor, barb adaptor, connector plug with flying lead & sensor.Sensors and Connectors FAQs...

AEM offers several sensor and Plug & Pin connector kits for vehicles that require additional outputs and/or upgraded hardware over existing sensors. Available sensors include boost/backpressure sensors, exhaust gas temperature (EGT) sensors, nitrous oxide/brake pressure sensors, UEGO replacement sensors, inlet air temp sensors (IAT), K-Type sensors and more. All sensors come with a three- wire mating connector with 12" leads for ease of installation.

High-quality sealed sensor housings
Mating connector and 12" leads included (sensors)
Accurate and affordable!


Our price: $155.25
Quantity
AEM Universal 100 PSIG Sensor Kit
Part #: 30-2130-100
100 PSIG sensor kit. Stainless steel sensor body with 1/8-NPT male thread. Includes -4 adaptor, barb adaptor, connector plug with flying lead & sensor.

AEM offers several sensor and Plug & Pin connector kits for vehicles that require additional outputs and/or upgraded hardware over existing sensors. Available sensors include boost/backpressure sensors, exhaust gas temperature (EGT) sensors, nitrous oxide/brake pressure sensors, UEGO replacement sensors, inlet air temp sensors (IAT), K-Type sensors and more. All sensors come with a three- wire mating connector with 12" leads for ease of installation.

High-quality sealed sensor housings
Mating connector and 12" leads included (sensors)
Accurate and affordable!


Our price: $155.25
Quantity
  •  per page