Extreme Turbo Systems


ETS Air Intake System - EVO X


The ETS MAF Intake Includes a huge 5" inlet K+N air filter which feeds the intake pipe via the ETS EVO X MAF adapter which is milled on the ETS lathe for the perfect transition to the inlet diameter of the MAF sensor tube.  With a built in dowel pin and precise inner diameter to make a 100% seal with the rubber grommet, this piece installs and fits as if it had a Mitsubishi part number.  The system is then braced to the chassis with an aluminum bracket to ensure no movement or vibration.  A single-piece mandrel bent 3" intake pipe makes the connection between the MAF and turbo with a smooth transition recirculation fitting for an easy connection to the BOV discharge.
The ETS Mitsubishi Evolution X Intake includes a 5.0" velocity stack making it the largest intake on the market.  This intake has been proven to gain over 56whp when used with a manual boost controller at 22psi.

    5" KN Filter
    ETS Milled MAF Adapter
    Perfrect Transition From Adapter To MAF
    Blow Off Valve Recirculation Tube
    Includes heat shield to prevent idle surge.
    BOV Vacuum Line
    All Couplers, Clamps and Hardware.
    +56whp when used with a boost controller @ 22psi

Our price: $296.95
ETS High Flow Cat Test Pipe - EVO X
Part #: ETS_EvoX_Cat_Pipe

 The ETS Evolution X High Flow Cat Test Pipe is a direct replacement of the factory catalytic pipe.  This has been dyno tested for a 10-15whp increase over the factory catalytic pipe.  Works with factory downpipe and factory exhaust system as well as any other aftermarket exhaust system that mounts in the factory location.


    Direct Replacement J-Pipe O2 Bung (Prevents Check Engine Lights)
    Optional Wideband o2 bung
    Stainless Steel
    Factory bend to clear the driveshaft unlike the competitors who use a straight pipe that will rub against the driveshaft.
    200 Cell High Flow Cat - Metal Core

Catalytic Converter Dimensions
Inlet Diameter - 3"
Outlet Diameter - 3"
Outer Shell Size - 4.00" O.D.
Overall Length - 10"
Metal Core Catalytic Converters are superior to traditional ceramic core converters in many ways:
- 100% Stainless Steel construction
- Metal Monolith is much more resistant to the effects of vibration than traditional ceramic bricks and capable of withstanding higher operating temperatures.
- 200 cell per Sq. Inch catalyst flows at 578 CFM, up to 40% better than a typical ceramic core converter.
Note: Dyno Graph is of the standard test pipe for reference.

Fits: 2008-2015 Lancer EVO X

Part# ETS_EvoX_Cat_Pipe

Our price: $359.95
ETS V2 Extreme Exhaust System - 2008-2015 EVO X
Part #: ETS_EvoX_Extreme

SKU: ETS_EvoX_Extreme

The ETS Mitsubishi Evo X V2 Extreme Exhaust System is a direct replacement of the factory cat back exhaust system.  This exhaust was designed for the true enthusiast looking for maximum performance with no mufflers or restrictions in the complete exhaust system.  This is one of the loudest exhaust systems on the market. This exhaust system is 100% stainless steel and made right here at our facility. The exhaust system features a 3.0" mid pipe that tucks up tightly against the underside of the vehicle giving you more ground clearance then any other exhaust on the market. The mid pipe connects to the rear section using a 3.0" v-band connection. The v-band connection provides a leak free seal and allows for a quick change race pipe for the drag strip! Each tip is centered perfectly in the bumper opening.


    Full 3" Manderal Bent Stainless Steel Piping
    3" V-Band
    No Mufflers

*Note: If using a stock catalytic converter select the adapter flange in the drop downs below.

Our price: $869.95
Extreme Dimensions 1999-2004 Ford Mustang Duraflex Colt Body Kit - 4 Piece
Part #: 110230

Extreme Dimensions 1999-2004 Ford Mustang Duraflex Colt Body Kit - 4 Piece

Part # 110230

Fits: 1999-2004 Ford Mustang. Fits All Models, Base Model, GT, Cobra, Mach 1.

Trim: ALL

Material: FRP (Fiberglass Reinforced Plastics)

1999-2004 Ford Mustang Duraflex Colt Body Kit - 4 Piece - Includes
- Colt Front Bumper Cover (102077)
- Colt Rear Bumper Cover (102079)
- Colt Side Skirts Rocker Panels (102080)

Hand laid, high quality 6 oz. fiberglass
Signature black finish
High quality weather resistant aluminum mesh grille (where applicable)
Proprietary polymer blend for maximum flexibility
Increased durability and longer service life
Reduced damage rate up to 75%

Our price: $385.95